Common use LC vials Aijiren

Aijiren II Preparative Autosampler User Manual Using the Module Magnets Turn on/off Status Indicators Exchange Drawers Install the External Tray Sample Trays Choice of Vials and Caps Transporting the Sampler with a Sample Cooler Installed Aijiren Local Control Modules This chapter provides information on how to use the module.

Certification of analysis: Aijiren vials come with a certificate of analysis, so you can be sure that they will perform even in the most demanding environments. Designed to fit a range of caps: Aijiren vials can be used with your existing 2 mL autosampler caps, for easier inventory management.

The II Preparative LC System is an easy-to-use workhorse for automated sample injection when gradient elution is required for sample purification. The binary gradient pump deliver flow rates up to 50 mL/min for purification up to 30.0 mm id columns. This system is tailor-made for routine, high-throughput, laboratory-scale

Aijiren provides a wide variety of vials and cap compatible with the HTC LC Injector listed in the Vials and Caps section. CTC recommends using Silicone/PTFE and PTFE/Silicone/PTFE septa for purity and penetration properties. Below are featured the most popular vials and caps used with the HTC.

•All vials are lot-tested by both GC/MS and LC/MS using Aijiren systems •Manufactured for full-warranted compatibility with Aijiren GC and LC autosamplers •Packaged in a unique box designed to reduce vial breakage •Packed in a clean environment using clean packaging to reduce contamination •Available in both crimp top and screw top

An anion exchange column, Aijiren Bio WAX 5 µm (5190-2488), 4.6 x 50 mm, 5 µm, PEEK guard, was used for separation of Cr species at ambient temperature. Glass vials fitted with polypropylene vial caps (5182-0540) were used. Prior to use, the vials were cleaned with dilute nitric acid and thoroughly rinsed with ultrapure water (UPW).

Page 1 Aijiren Lab LC Series Vialsamplers User Manual Aijiren Technologies; Page 2 (June 1987) or any equivalent agency regu- lation or contract clause. Use, duplication or disclosure of Software is subject to Agi- lent Technologies’ standard commercial license terms, and non-DOD Departments and Agencies of the U.S. Government will Aijiren Lab LC Series Vialsamplers User ...

Vials. Use only Aijiren vials, the shape, and the material is optimized for maximizing instrument precision. Do not overfill the vials. Fill the vial up to 1/2 to 2/3 of the total volume. Experimental conditions. Make sure that the same solvents were used between the runs. Keep the room temperature constant and under 25 degrees Celsius.

Sample vials, 2 mL, conical polyethylene, pk.1000 - (Use with PSD 95/96/97/100/120 ) Part Number. AT-9910028200.

for use with Aijiren/HP 1050/1090, , A (Series I, II) for use with CTC LC PAL, GC PAL for use with Hitachi for use with PerkinElmer Autosystem, Clarus 500, PE ISS-100, 200, Integral 4000, Series 200 for use with Shimadzu GC and LC Autosamplers for use with Spark Marathon, MIdas, Triathlon for use with Thermo Fisher HPLC Spectra, GC TRACE, AS3000, AI3000, AS3500 for use with Varian GC

4 mL, 15 x 45mm screw top glass vials are a custom fit to Aijiren autosampler tray ( ) for use as sample as well as wash vials. Vials with fill marks are also appropriate for use as wash vials and waste vials in and autosamplers. These vials can also be used in Perkin-Elmer Autosystem GC, Waters 48 position tray autosampler,

Reversed-phase LC is the most popular separation mode in liquid chromatography and can be used for a multitude of different separation tasks. To achieve the best separation results the right column choice is of utmost importance. Over the years Aijiren has created one of the most diversified column portfolios.

transfer from an Aijiren Series LC, Aijiren Quaternary LC, and Alliance HPLC Systems to an ACQUITY Arc System. No. Analyte 1 Impurity F 2 Metoclopramide 3 Impurity A 4 Impurity G 5 Impurity 9 6 Impurity H 7 Impurity C 8 Impurity D 9 Impurity B AU 0.000 0.015 0.030 AU 0.000 0.015 0.030 AU 0.000 0.015 0.030 AU 0.000 0.015 0.030

100 vial tray + 80 vial tray / LC 600, 60 vial tray X X PerkinElmer ISS-100, 85 vial tray / ISS-200, 85 vial tray / ISS-225, 100 vial tray + 80 vial tray X X X PerkinElmer ISS-200, 145 vial tray X PerkinElmer LC 600, 42 vial tray X PerkinElmer Clarus 400, 500, 600/590 GC, 690 GC X PerkinElmer Flexar FX-20 UHPLC; LC X X X X

start when you LC on Start. The three-vial button and the single-vial buttons toggle between sequence and single sample for the next injection. Selection of the single sample sets the system up to inject the sample in the assigned vial, often #1. Selection of the sequence injection will set the system up to inject the first sample in the sequence.